SNOW CONE MACHINES BY PARAGON, ARCTIC BLAST MODEL # 6133310

A hard-working, economical option, the Arctic Blast Snow Cone Machine has Tinted High-Impact Polycarbonate side panels and Door

 

Features include:

Our smallest cabinet of all the Paragon Snow Cone Machines, but full of features. Easy to move. Heavy duty construction. Stainless Steel and aluminum construction. Removable slanted drain deck, 36” drain tube, and scoop included. Blue-tinted polycarbonate panels.
Clear front access door.
1/3 HP motor, 500 lbs per hr.
Optional cup dispenser.

500 lbs/hr

Approved as: (ETL tested to) UL 763 •CSA 22.2 •NSF 12 • CE

Volts: 120

Watts: 635

Amps: 5.3

Weight:		50.00 pounds
Dimensions:		16" X 14" X 24"

Paragon Arctic Blast Snow Cone Machines have powerful motors, sturdy cabinets and
attention-getting graphics. Just add ice and syrup for great profits! We have four models to suit every customers’ needs. The machines feature:

Heavy-Duty Motor

This Snow Cone Machine has a tough 1/3 horsepower, 1725-RPM motor can shave more than 500 lbs. of cube or chunk ice per hour. The motor has a safety switch prevents accidental start-up.

Cast Aluminum Components

Horns, pushers and shaver head assembly are made of strong, cast aluminum. The shave head assembly has two, high-grade stainless steel blades that are adjustable and easy to replace. Paragon Snow Cone Machines are made in the USA.

SUPER-FAST SHIPPING!!!!! On Snow Cone Machines. Item usually ships next business day NO P.O. BOXES!!! Posted shipping is to the lower 48 states only. Contact us for special pricing for international locations. BUYER pays all shipping and handling. ALWAYS inspect all items for damage BEFORE accepting them from shipper. If the product arrives damaged, DO NOT ACCEPT IT. If the Item is accepted and damaged during shipping the buyer must make a claim with the shipment carrier first. Thank you for shopping!

UPS GROUND TRANSIT TIME FORM IOWA

• OPERATING INSTRUCTIONS FOR YOUR SNOW CONE MACHINE
  
  
  Be sure your Snow Cone Machine is connected to properly grounded 120 volt power supply with 15 amp circuit
   (230 volts for export models)
  
  Shaving Ice
  
  
  1. Turn POWER switch ON (Not used on The Cooler and The Blast).
  2. Fill the ice horn with ice.
  3. Press and hold the MOTOR switch to activate blades and begin shaving ice.
  4. While holding MOTOR switch down, apply steady downward pressure to the ice pusher
  5. Release the MOTOR switch when finished.
  6. Repeat steps 2-5 for additional batches.
  
  Cleaning Procedures
  
  1. Remove all ice from the ice horn and storage compartment.
  2. Operate the motor for several minutes to remove any water collection on the cutter head.
  3. Turn off the POWER switch. (Not used on all models.)
  4. Unplug the power cord from the electrical outlet.
  5. Using a clean cloth, wipe down the following items.
  • The inner surface of the ice horn (Caution: Sharp Blades)
  • The outside surface of the ice horn casting.
  • The ice pusher.
  • All interior and exterior surfaces.
  6. To clean the water collection tray.
  • Tilt tray to drain the water trapped in the drain cavity.
  • Slip the drain hose off the nipple fitting.
  • Lift the tray out of the cabinet
  • Clean tray and area below tray with clean cloth.
  
  Note: FDA approved cleaners may be used to clean your Snow Cone Machine when required for sanitation. Do not use ammonia based cleaners on polycarbonate door and/or side panels.
  
  BLADES ARE SHARP AND OPERATE AT HIGH SPEEDS! Please be sure to keep all body parts and any objects such as picks or scoops away from the ice horn while POWER is on!